Set device version from config.h for V-USB boards (#7316)

* Add support for custom polling interval and power usage on V-USB boards

* Use 1ms as default for now

keyboards/ares/config.h

@@ -21,6 +21,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    LSJ
 #define PRODUCT         QMK Firmware for Ares
 

keyboards/ares/usbconfig.h

@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -238,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'L', 'S', 'J'

keyboards/bfake/config.h

@@ -22,6 +22,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    NotActuallyWinkeyless
 #define PRODUCT         b.fake
 

keyboards/bfake/usbconfig.h

@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -238,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/coseyfannitutti/discipad/config.h

@@ -50,6 +50,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define DIODE_DIRECTION COL2ROW
 
 #define NO_UART 1
+#define USB_MAX_POWER_CONSUMPTION 100
 
 /*
  * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.

keyboards/coseyfannitutti/discipad/usbconfig.h

@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -239,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x01, 0x00
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'c','o','s','e','y','f','a','n','n','i','t','u','t','t','i'

keyboards/coseyfannitutti/discipline/config.h

@@ -48,6 +48,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define DIODE_DIRECTION COL2ROW
 
 #define NO_UART 1
+#define USB_MAX_POWER_CONSUMPTION 100
 
 /*
  * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.

keyboards/coseyfannitutti/discipline/usbconfig.h

@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -239,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x01, 0x00
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'c','o','s','e','y','f','a','n','n','i','t','u','t','t','i'

keyboards/donutcables/budget96/config.h

@@ -21,6 +21,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    DonutCables
 #define PRODUCT         budget96
 

keyboards/donutcables/budget96/usbconfig.h

@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -237,7 +227,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'D', 'o', 'n', 'u', 't', 'C', 'a', 'b', 'l', 'e', 's'

keyboards/eve/meteor/config.h

@@ -21,6 +21,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    EVE
 #define PRODUCT         Meteor
 

keyboards/eve/meteor/usbconfig.h

@@ -98,20 +98,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -227,7 +217,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'
@@ -380,4 +370,4 @@ section at the end of this file).
 #define USB_INTR_ENABLE_BIT     INT1
 /* #define USB_INTR_PENDING        EIFR */
 #define USB_INTR_PENDING_BIT    INTF1
-#define USB_INTR_VECTOR         INT1_vect
+#define USB_INTR_VECTOR         INT1_vect

keyboards/exclusive/e6v2/le_bmc/usbconfig.h

@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -237,7 +227,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'E', 'x', 'c', 'l', 'u', 's', 'i', 'v', 'e'

keyboards/exclusive/e6v2/oe_bmc/usbconfig.h

@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -237,7 +227,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'E', 'x', 'c', 'l', 'u', 's', 'i', 'v', 'e'

keyboards/exent/usbconfig.h

@@ -98,20 +98,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL 1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED 0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER 500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE 1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -227,7 +217,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION 0x00, 0x02
+#define USB_CFG_DEVICE_VERSION (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME 'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/facew/config.h

@@ -21,6 +21,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    NotActuallyWinkeyless
 #define PRODUCT         facew
 

keyboards/facew/usbconfig.h

@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -237,7 +227,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'S', 'p', 'r', 'i', 't'

keyboards/ft/mars80/usbconfig.h

@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -237,7 +227,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'f', 't'

keyboards/gingham/config.h

@@ -51,6 +51,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define DIODE_DIRECTION COL2ROW
 
 #define NO_UART 1
+#define USB_MAX_POWER_CONSUMPTION 100
 
 /*
  * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.

keyboards/gingham/usbconfig.h

@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -239,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x01, 0x00
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'Y','i','a','n','c','a','r','-','D','e', 's', 'i', 'g', 'n', 's'

keyboards/gray_studio/hb85/config.h

@@ -19,6 +19,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422F
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    Gray Studio
 #define PRODUCT         HB85
 

keyboards/gray_studio/hb85/usbconfig.h

@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -237,7 +227,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'G', 'r', 'a', 'y', ' ', 'S', 't', 'u', 'd', 'i', 'o'

keyboards/handwired/hnah40/config.h

@@ -78,6 +78,8 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 // #define GRAVE_ESC_CTRL_OVERRIDE
 
+#define USB_MAX_POWER_CONSUMPTION 100
+
 /*
  * Force NKRO
  *

keyboards/handwired/hnah40/usbconfig.h

@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -239,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x01
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'H','n','a','h','K','B'

keyboards/jc65/v32a/config.h

@@ -21,6 +21,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x1234
 #define PRODUCT_ID      0x5679
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    winkeyless.kr
 #define PRODUCT         JC65 PS2AVRGB
 

keyboards/jc65/v32a/usbconfig.h

@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -238,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/jj40/config.h

@@ -18,6 +18,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 // TODO: share these strings with usbconfig.h
 // Edit usbconfig.h to change these.
 #define MANUFACTURER    Kprepublic
@@ -45,6 +46,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define DEBOUNCE 5
 
 #define NO_UART 1
+#define USB_MAX_POWER_CONSUMPTION 100
 
 /* key combination for magic key command */
 /* defined by default; to change, uncomment and set to the combination you want */

keyboards/jj40/usbconfig.h

@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -239,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/jj4x4/config.h

@@ -21,6 +21,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 // TODO: share these strings with usbconfig.h
 // Edit usbconfig.h to change these.
 #define MANUFACTURER    Kprepublic
@@ -48,6 +49,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define DEBOUNCE 5
 
 #define NO_UART 1
+#define USB_MAX_POWER_CONSUMPTION 100
 
 /* key combination for magic key command */
 /* defined by default; to change, uncomment and set to the combination you want */

keyboards/jj4x4/usbconfig.h

@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -239,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/jj50/config.h

@@ -24,6 +24,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 // TODO: share these strings with usbconfig.h
 // Edit usbconfig.h to change these.
 #define MANUFACTURER    kprepublic

keyboards/jj50/usbconfig.h

@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -238,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'K', 'P', 'R', 'e', 'p', 'u', 'b', 'l', 'i', 'c'

keyboards/kbdfans/kbdpad/mk1/config.h

@@ -21,6 +21,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    KBDfans
 #define PRODUCT         KBDPAD-MKI
 

keyboards/kbdfans/kbdpad/mk1/usbconfig.h

@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -237,7 +227,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/mechmini/v1/usbconfig.h

@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -238,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/mehkee96/config.h

@@ -5,6 +5,7 @@
 /* USB Device descriptor parameter */
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    mehkee
 #define PRODUCT         96kee
 

keyboards/mehkee96/usbconfig.h

@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -238,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/mt40/usbconfig.h

@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -238,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x03
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'T', 'h', 'o', 'm', 'a', 's', 'D', 'e', 'h', 'a', 'e', 'z', 'e'

keyboards/panc60/config.h

@@ -21,6 +21,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    Panc Interactive
 #define PRODUCT         panc60
 

keyboards/panc60/usbconfig.h

@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -237,7 +227,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/pearl/config.h

@@ -21,6 +21,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID    0xFEED
 #define PRODUCT_ID   0x0348
+#define DEVICE_VER   0x0200
 #define MANUFACTURER Pearl Boards
 #define PRODUCT      Pearl
 #define DESCRIPTION  40% keyboard

keyboards/pearl/usbconfig.h

@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -237,7 +227,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/percent/canoe/config.h

@@ -22,6 +22,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    NotActuallyPercent
 #define PRODUCT         CANOE
 

keyboards/percent/canoe/usbconfig.h

@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -238,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/percent/skog/config.h

@@ -20,6 +20,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 
 #define MANUFACTURER    Percent
 #define PRODUCT         Skog TKL

keyboards/percent/skog/usbconfig.h

@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -238,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'P','e','r','c','e','n','t'

keyboards/percent/skog_lite/config.h

@@ -21,6 +21,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    Percent
 #define PRODUCT         Skog Lite
 

keyboards/percent/skog_lite/usbconfig.h

@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -237,7 +227,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/plaid/config.h

@@ -50,6 +50,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define DIODE_DIRECTION COL2ROW
 
 #define NO_UART 1
+#define USB_MAX_POWER_CONSUMPTION 100
 
 /*
  * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.

keyboards/plaid/usbconfig.h

@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -239,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x01
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'd','m','9','r','e','c','o','r','d','s'

keyboards/singa/config.h

@@ -21,6 +21,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    Singa Keyboards
 #define PRODUCT         Singa
 

keyboards/singa/usbconfig.h

@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -237,7 +227,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/tgr/alice/config.h

@@ -19,6 +19,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422E
+#define DEVICE_VER      0x0200
 // TODO: share these strings with usbconfig.h
 // Edit usbconfig.h to change these.
 #define MANUFACTURER    TGR

keyboards/tgr/alice/usbconfig.h

@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -238,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'T', 'G', 'R'

keyboards/tgr/jane/config.h

@@ -21,6 +21,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    TGR
 #define PRODUCT         Jane
 

keyboards/tgr/jane/usbconfig.h

@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -237,7 +227,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/unikorn/config.h

@@ -21,6 +21,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    Singa and TGR
 #define PRODUCT         Unikorn 60
 

keyboards/unikorn/usbconfig.h

@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -237,7 +227,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     's', 'i', 'n', 'g', 'a', 't', 'g', 'r'

keyboards/winkeyless/bface/config.h

@@ -20,6 +20,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 // You can edit those at usbconfig.h about line 250. These values will
 // unforunatly be ignored so far
 #define MANUFACTURER    winkeyless.kr

keyboards/winkeyless/bface/usbconfig.h

@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -237,7 +227,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/winkeyless/bmini/config.h

@@ -22,6 +22,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    winkeyless.kr
 #define PRODUCT         B.mini
 

keyboards/winkeyless/bmini/usbconfig.h

@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -238,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/winkeyless/bminiex/config.h

@@ -21,6 +21,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422E
+#define DEVICE_VER      0x0200
 #define MANUFACTURER    winkeyless.kr
 #define PRODUCT         B.mini Ex
 

keyboards/winkeyless/bminiex/usbconfig.h

@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -238,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

keyboards/ymd75/config.h

@@ -24,6 +24,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 
 // TODO: share these strings with usbconfig.h
 // Edit usbconfig.h to change these.

keyboards/ymd75/usbconfig.h

@@ -109,20 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -238,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'Y', 'M', 'D', 'K'

keyboards/ymd96/config.h

@@ -23,6 +23,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 // Edit usbconfig.h to change these.
 #define MANUFACTURER    ymdkey
 #define PRODUCT         ymd96
@@ -42,6 +43,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define TAPPING_TOGGLE 3
 
 #define NO_UART 1
+#define USB_MAX_POWER_CONSUMPTION 100
 
 /* RGB underglow */
 // The RGB_DI_PIN value seems to be shared between all PS2AVRGB boards.

keyboards/ymd96/usbconfig.h

@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -239,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'y','m','d','k','e','y'

keyboards/ymdk/bface/config.h

@@ -19,6 +19,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 // You can edit those at usbconfig.h about line 250. These values will
 // unforunatly be ignored so far
 #define MANUFACTURER    YMDK

keyboards/ymdk/bface/usbconfig.h

@@ -108,20 +108,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER           500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -237,7 +227,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'Y', 'M', 'D', 'K'

keyboards/ymdk_np21/config.h

@@ -22,6 +22,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VENDOR_ID       0x20A0
 #define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0200
 // TODO: share these strings with usbconfig.h
 // Edit usbconfig.h to change these.
 #define MANUFACTURER    ymdk
@@ -41,6 +42,8 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define NO_UART 1
 
+#define USB_MAX_POWER_CONSUMPTION 100
+
 /* RGB underglow */
 // The RGB_DI_PIN value seems to be shared between all PS2AVRGB boards.
 // The same pin is used on the JJ40, at least.

keyboards/ymdk_np21/usbconfig.h

@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -239,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

layouts/community/ortho_4x12/jotix/keymap.c

@@ -4,13 +4,11 @@ enum layers {
   _QWERTY,
   _LOWER,
   _RAISE,
-  _GAME
 };
 
 #define LOWER   MO(_LOWER)
 #define RAISE   MO(_RAISE)
 #define TGLOWER TG(_LOWER)
-#define TGGAME  TG(_GAME)
 
 static bool is_ctl_pressed;
 static bool is_esc_pressed;
@@ -20,23 +18,23 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 
 [_QWERTY] = LAYOUT_ortho_4x12 (
 // ┌───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┐
-     KC_ESC, KC_Q  , KC_W  , KC_E  , KC_R  , KC_T  , KC_Y  , KC_U  , KC_I  , KC_O  , KC_P  ,KC_BSPC,
+    KC_ESC, KC_Q,   KC_W,   KC_E,   KC_R,   KC_T,   KC_Y,   KC_U,   KC_I,   KC_O,   KC_P,   KC_BSPC,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-     KC_TAB, KC_A  , KC_S  , KC_D  , KC_F  , KC_G  , KC_H  , KC_J  , KC_K  , KC_L  ,KC_SCLN,KC_QUOT,
+    KC_TAB, KC_A,   KC_S,   KC_D,   KC_F,   KC_G,   KC_H,   KC_J,   KC_K,   KC_L,   KC_SCLN,KC_QUOT,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-    KC_LSFT, KC_Z  , KC_X  , KC_C  , KC_V  , KC_B  , KC_N  , KC_M  ,KC_COMM, KC_DOT,KC_SLSH, KC_ENT,
+    KC_LSFT,KC_Z,   KC_X,   KC_C,   KC_V,   KC_B,   KC_N,   KC_M,   KC_COMM,KC_DOT, KC_SLSH,KC_ENT,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-    KC_LCTL,KC_LGUI,KC_LALT,KC_RALT, LOWER , KC_SPC, KC_SPC, RAISE ,KC_LEFT,KC_DOWN, KC_UP ,KC_RGHT
+    KC_LCTL,KC_LGUI,KC_LALT,KC_RALT,LOWER,  KC_SPC, KC_SPC, RAISE,  KC_LEFT,KC_DOWN,KC_UP,  KC_RGHT
 // └───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┘
 ), 
 
 [_LOWER] = LAYOUT_ortho_4x12 (
 // ┌───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┐
-     KC_GRV,  KC_1 ,  KC_2 ,  KC_3 ,  KC_4 ,  KC_5 ,  KC_6 ,  KC_7 ,  KC_8 ,  KC_9 ,  KC_0 ,_______,
+    KC_GRV, KC_1,   KC_2,   KC_3,   KC_4,   KC_5,   KC_6,   KC_7,   KC_8,   KC_9,   KC_0,   _______,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-    _______,KC_VOLD,KC_MUTE,KC_VOLU,_______, TGGAME,_______,_______,_______,_______,_______,_______,
+    _______,KC_VOLD,KC_MUTE,KC_VOLU,KC_MINS, KC_EQL,KC_LBRC,KC_RBRC,_______,_______,_______,_______,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-    _______,KC_MPRV,KC_MPLY,KC_MNXT,_______,_______,_______,_______,_______,_______,_______,_______,
+    _______,KC_MPRV,KC_MPLY,KC_MNXT,KC_UNDS,KC_PLUS,KC_LCBR,KC_RCBR,_______,_______,_______,_______,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
     _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______
 // └───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┘
@@ -44,61 +42,46 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 
 [_RAISE] = LAYOUT_ortho_4x12 (
 // ┌───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┐
-    KC_TILD,KC_EXLM, KC_AT ,KC_HASH, KC_DLR,KC_PERC,KC_CIRC,KC_AMPR,KC_ASTR,KC_LPRN,KC_RPRN, KC_DEL,
+    KC_TILD,KC_EXLM,KC_AT,  KC_HASH,KC_DLR, KC_PERC,KC_CIRC,KC_AMPR,KC_ASTR,KC_LPRN,KC_RPRN,KC_DEL,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-    KC_CAPS, KC_F1 , KC_F2 , KC_F3 , KC_F4 , KC_F5 , KC_F6 ,KC_MINS, KC_EQL,KC_LBRC,KC_RBRC,KC_BSLS,
+    KC_CAPS,KC_F1,  KC_F2,  KC_F3,  KC_F4,  KC_F5,  KC_F6,  KC_MINS,KC_EQL, KC_LBRC,KC_RBRC,KC_BSLS,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-    _______, KC_F7 , KC_F8 , KC_F9 , KC_F10, KC_F11, KC_F12,KC_UNDS,KC_PLUS,KC_LCBR,KC_RCBR,KC_PIPE,
+    _______,KC_F7,  KC_F8,  KC_F9,  KC_F10, KC_F11, KC_F12, KC_UNDS,KC_PLUS,KC_LCBR,KC_RCBR,KC_PIPE,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
     _______,_______,_______,_______,TGLOWER,_______,_______,_______,KC_HOME,KC_PGDN,KC_PGUP, KC_END
 // └───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┘
 ),
 
-[_GAME] = LAYOUT_ortho_4x12 (
-// ┌───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┐
-    _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,
-// ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-    _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,
-// ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-    _______,_______,_______,_______,_______,_______,_______,_______,_______,_______, KC_UP ,_______,
-// ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-    _______,_______,_______,_______,_______,_______,_______,_______,KC_SLSH,KC_LEFT,KC_DOWN,KC_RGHT
-// └───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┘
-),
-
 };
 
 uint32_t layer_state_set_user(uint32_t state) {
   #ifdef JOTANCK_LEDS
-  switch (biton32(state)) {
-  case _LOWER:
+  if (biton32(state) == _LOWER) {
     writePinHigh(JOTANCK_LED1);
-    writePinLow(JOTANCK_LED2);
-    break;
-  case _RAISE:
+  } else {
     writePinLow(JOTANCK_LED1);
-    writePinHigh(JOTANCK_LED2);
-    break;
-  case _GAME:
-    writePinHigh(JOTANCK_LED1);
-    writePinHigh(JOTANCK_LED2);
-    break;
-  default:
-    writePinLow(JOTANCK_LED1);
-    writePinLow(JOTANCK_LED2);
-    break; 
-  };
+  }
   #endif
   return state;
 }
 
-/*  
-void led_set_user(uint8_t usb_led) {
-  if (!(IS_LED_ON(usb_led, USB_LED_NUM_LOCK))) {
+bool led_update_user(led_t led_state) {
+
+  // NumLock allways on
+  if (!led_state.num_lock) {
     tap_code(KC_NUMLOCK);
   }
+
+  #ifdef JOTANCK_LEDS
+  // CapsLock led
+  if (led_state.caps_lock) {
+    writePinHigh(JOTANCK_LED2);
+  } else {
+    writePinLow(JOTANCK_LED2);
+  }
+  #endif
+  return true;
 }
-*/
 
 bool process_record_user(uint16_t keycode, keyrecord_t *record) {
   switch (keycode) {

quantum/template/ps2avrgb/usbconfig.h

@@ -98,20 +98,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL 1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED 0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-#define USB_CFG_MAX_BUS_POWER 500
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE 1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -227,7 +217,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION 0x00, 0x02
+#define USB_CFG_DEVICE_VERSION (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME 'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'

tmk_core/protocol/vusb/vusb.c

@@ -345,6 +345,15 @@ const PROGMEM uchar mouse_hid_report[] = {
     0xc0,                      // END_COLLECTION
 };
 
+#ifndef USB_MAX_POWER_CONSUMPTION
+#    define USB_MAX_POWER_CONSUMPTION 500
+#endif
+
+// TODO: change this to 10ms to match LUFA
+#ifndef USB_POLLING_INTERVAL_MS
+#    define USB_POLLING_INTERVAL_MS 1
+#endif
+
 /*
  * Descriptor for compite device: Keyboard + Mouse
  *
@@ -366,7 +375,7 @@ const PROGMEM char usbDescriptorConfiguration[] = {
 #    else
     (1 << 7), /* attributes */
 #    endif
-    USB_CFG_MAX_BUS_POWER / 2, /* max USB current in 2mA units */
+    USB_MAX_POWER_CONSUMPTION / 2, /* max USB current in 2mA units */
 
     /*
      * Keyboard interface
@@ -393,7 +402,7 @@ const PROGMEM char usbDescriptorConfiguration[] = {
     (char)0x81,                      /* IN endpoint number 1 */
     0x03,                            /* attrib: Interrupt endpoint */
     8, 0,                            /* maximum packet size */
-    USB_CFG_INTR_POLL_INTERVAL,      /* in ms */
+    USB_POLLING_INTERVAL_MS,         /* in ms */
 #    endif
 
     /*
@@ -424,7 +433,7 @@ const PROGMEM char usbDescriptorConfiguration[] = {
     (char)(0x80 | USB_CFG_EP3_NUMBER), /* IN endpoint number 3 */
     0x03,                              /* attrib: Interrupt endpoint */
     8, 0,                              /* maximum packet size */
-    USB_CFG_INTR_POLL_INTERVAL,        /* in ms */
+    USB_POLLING_INTERVAL_MS,           /* in ms */
 #    endif
 };
 #endif